| themaPoster http://poster.themasoftware.com/forum/ |
|
| [varios.biz] http://poster.themasoftware.com/forum/viewtopic.php?f=19&t=9233 |
Page 1 of 1 |
| Author: | rocky [ April 22nd, 2018, 9:00 pm ] |
| Post subject: | [varios.biz] |
Hello. How to be if when scanning the forum the program does not define it because the forum is not available for the Russian IP address Access restricted Access to the requested resource is limited by a court decision or on other grounds, established by the legislation of the Russian Federation forum can not be added to the program because it shows an incorrect address when scanning the program works with my native Russian ip address please add to the program the ability to scan the forum under the control of the proxy-this is the very first stage of defining the forum and its engine |
|
| Author: | rocky [ April 22nd, 2018, 11:09 pm ] |
| Post subject: | Re: How to be if when scanning the forum the program does no |
example the forum, from the my native Russian ip address the program can not scan this forum http://varios.biz |
|
| Author: | Freddy [ April 23rd, 2018, 8:18 am ] |
| Post subject: | Re: How to be if when scanning the forum the program does no |
Hi, you set proxy in "CONFIG" -> "Proxy" and enable it. The proxy will be used when adding forum. |
|
| Author: | rocky [ April 23rd, 2018, 11:58 am ] |
| Post subject: | Re: How to be if when scanning the forum the program does no |
the wrong answer before adding a forum it should be scanned by the program and then after the successful scan is added to the database the given forum is not scanned by the program because my native Russian ip address does not recognize it please add to the program the ability to scan the forum under the control the proxy-this is the very first stage defining the forum and its engine |
|
| Author: | Freddy [ April 23rd, 2018, 12:50 pm ] |
| Post subject: | Re: How to be if when scanning the forum the program does no |
You can already do that. In "CONFIG" -> Proxy" add the proxy and enable it. The program will use that proxy for all requests. |
|
| Author: | rocky [ April 23rd, 2018, 3:34 pm ] |
| Post subject: | Re: How to be if when scanning the forum the program does no |
I do not need for all requests, I need only for a certain forum please add to the program the ability to scan the forum under the control of the proxy-this is the very first stage of defining the forum and its engine |
|
| Author: | rocky [ April 23rd, 2018, 3:37 pm ] |
| Post subject: | Re: How to be if when scanning the forum the program does no |
|
|
|
| Author: | rocky [ April 23rd, 2018, 3:40 pm ] |
| Post subject: | Re: How to be if when scanning the forum the program does no |
after scanning the forum the program shows the wrong forum address Instead of the address http://varios.biz the program determines the address http://warning.rt.ru and if the address that the program offered does I will not change, then the program does not determine the forum's engine http://warning.rt.ru such a site does not exist on the Internet and this is not the address of the forum that I need |
|
| Author: | Freddy [ April 23rd, 2018, 3:44 pm ] |
| Post subject: | Re: How to be if when scanning the forum the program does no |
You forgot to enable proxy in "CONFIG" -> "Proxy". They are banning your IP address. You must use proxy. You can as well add proxy for rank zero in "FORUMS" -> "Proxy" tab (before adding). |
|
| Author: | rocky [ April 23rd, 2018, 3:49 pm ] |
| Post subject: | Re: How to be if when scanning the forum the program does no |
I need so that the program to determine the address after scanning http://varios.biz but since my native ip address in the program is Russian and this forum is closed for Russian IP address then the program after scanning can not scan this forum on definition the engine |
|
| Author: | rocky [ April 23rd, 2018, 3:52 pm ] |
| Post subject: | Re: How to be if when scanning the forum the program does no |
I turned on the proxy but still the type of engine the program does not detect 
|
|
| Author: | Freddy [ April 23rd, 2018, 3:57 pm ] |
| Post subject: | Re: How to be if when scanning the forum the program does no |
Because you're using old version. Update to the latest version. That problem was only fixed in the latest version. |
|
| Page 1 of 1 | All times are UTC |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|